Drawing is a language, and reading it comes before writing it. I have seen technicians who could draft quickly but could not tell a section from an elevation, and I have seen newcomers learn in weeks because they read every sheet they touched. This test checks whether you can read: lines, symbols, scales, dimensions and the habits that stop expensive mistakes.
This free test has 30 multiple-choice questions with an answer key that explains every answer.
The Short Answer
- 30 questions: 10 core conventions, 10 reading and checking, 10 discipline and practice.
- No software knowledge needed.
- Covers lines, symbols, scale, dimensions, sections, schedules and status stamps.
- It is a self-assessment, not a certification.
- Conventions vary by office and standard, so always check the legend.
How This Test Works
- Take it without help. Use paper and a pencil for the calculations. Do not look up the answers.
- Write your answers down (for example, 1-B, 2-D) before you read the answer key.
- Check yourself against the answer key and read every explanation, including those for questions you got right.
- Score yourself with the bands below.
This is an informal self-assessment, not a certification, and employers’ tests differ. Software questions describe general behaviour. Menus and features vary by version, so check your employer’s version.
The Test (30 Questions)
Core Symbols and Conventions (Questions 1 to 10)
Lines, notes and the information on every sheet.
1. On a drawing, what does a thick continuous line normally represent?
- A. Hidden edges
- B. Visible object edges (outlines)
- C. Centre lines
- D. Dimension limits
2. What does a long-short-long chain line normally mark?
- A. A hidden edge
- B. A centre line or axis of symmetry
- C. A property line only
- D. A cut surface
3. A drawing note says ‘TYP.’ next to a dimension. What does this mean?
- A. The feature is a type of material
- B. The dimension is typical and applies to similar features
- C. The dimension is approximate
- D. The feature is optional
4. A drawing is marked ‘NTS’. What does that mean?
- A. Notes to supplier
- B. Not to scale
- C. New tolerance standard
- D. Nominal thread size
5. Where do you normally find the scale of a drawing?
- A. Only in the specifications
- B. In the title block or beneath the view
- C. In the revision cloud
- D. On the cover letter
6. A section line with arrows and the letter A at each end points to what?
- A. A dimension
- B. The cutting plane of section A, with arrows showing the viewing direction
- C. A hidden edge
- D. A grid line
7. What does a revision cloud draw attention to?
- A. The scale
- B. Changes made in the latest revision
- C. Errors that cannot be fixed
- D. The approved area
8. Which of these usually appears in a title block?
- A. Only the colours used
- B. Drawing number, title, revision, date and drawn or checked by
- C. Only the plot style
- D. A list of all the layers
9. A drawing shows ‘Ø25’. What does it describe?
- A. A radius of 25
- B. A diameter of 25 units
- C. A depth of 25
- D. A thread pitch of 25
10. On a floor plan, what does a door swing arc show?
- A. The door’s weight
- B. The direction the door opens
- C. The wall thickness
- D. The fire rating
Reading and Checking (Questions 11 to 20)
Dimensions, scale, details and what to do when something is unclear.
11. A wall is shown with dimensions 3,000, 2,400 and an overall of 5,400. What should you do if the overall reads 5,500?
- A. Use the larger number
- B. Use the smaller number
- C. Average the two
- D. Flag the discrepancy and ask the drawing author before building or drafting from it
12. When a drawing’s dimension conflicts with what you measure by scaling the print, which governs?
- A. The scaled measurement
- B. The larger number
- C. The measurement on the screen
- D. The written dimension, unless the drawing says otherwise
13. A detail bubble reads ‘5 over A-501’. What does it usually tell you?
- A. Five copies of A-501
- B. Section 5 at scale 501
- C. Revision 5 of the drawing
- D. Detail 5 is on sheet A-501
14. What does a 1:50 scale mean?
- A. 50 units on the drawing is one real unit
- B. The drawing is 50% of real size
- C. The drawing is 50 times larger than the object
- D. One unit on the drawing represents 50 of the same units in reality
15. An elevation mark reads ‘+3.200’ on a section. What is it?
- A. A dimension of a window
- B. The thickness of a slab
- C. The revision
- D. A level or height relative to the project’s datum
16. In a mechanical drawing, what does a feature control frame show?
- A. The material
- B. The scale
- C. The author
- D. A geometric tolerance applied to a feature
17. What does a hatch pattern in a section usually indicate?
- A. The colour of paint
- B. The direction of north
- C. The load
- D. The type of material cut by the section plane
18. A symbol you do not recognize appears on a drawing. What is the best first step?
- A. Guess from its shape
- B. Ignore it
- C. Delete it
- D. Check the legend or symbol list and the drawing standard
19. What is a schedule on an architectural drawing set?
- A. A construction timetable only
- B. A list of drawings only
- C. A budget
- D. A table listing items such as doors, windows or finishes with their data
20. What is the purpose of a general notes sheet?
- A. To list the plot settings
- B. To show only the site
- C. To show the revision history only
- D. To state requirements and conventions that apply to the whole set
Discipline and Practice (Questions 21 to 30)
Piping, welding, electrical, civil and professional habits.
21. A pipe isometric shows an elbow dimensioned from the centre of one fitting to the centre of the next. What type of dimensioning is this?
- A. Face-to-face dimensioning
- B. Centre-to-centre dimensioning
- C. Overall dimensioning only
- D. Angular dimensioning
22. What does a weld symbol’s arrow side and other side indicate?
- A. The colour of the weld
- B. Which side of the joint the weld is made on, relative to the arrow
- C. The weld’s strength
- D. The order of welding
23. In an electrical drawing set, what does a panel schedule list?
- A. Door hardware
- B. Circuits, breakers and loads for a panel
- C. Pipe sizes
- D. Structural members
24. Which sheet prefix is typically used for structural drawings in North America?
- A. A
- B. S
- C. M
- D. P
25. What do contour lines on a site plan show?
- A. Property boundaries
- B. Lines of equal ground elevation
- C. Roads only
- D. Underground pipes
26. A civil profile sheet shows a grade of ‘-2.0%’. What does the sign indicate?
- A. The grade rises
- B. The grade falls in the direction of increasing station
- C. The grade is flat
- D. The grade is a mistake
27. When two drawings in the set disagree, who should resolve it?
- A. The person who finds it, by choosing the cheaper option
- B. The designer of record, through the proper channel such as a request for information
- C. The plotter operator
- D. Nobody, because drawings are approximate
28. What does ‘AFF’ commonly mean on an architectural drawing?
- A. Approved for fabrication
- B. Above finished floor
- C. After final fixing
- D. Aligned with face of frame
29. What does ‘R’ next to a number on a part drawing mean?
- A. Revision
- B. Radius
- C. Roughness
- D. Reference
30. A drawing is stamped ‘FOR REVIEW ONLY’ or ‘NOT FOR CONSTRUCTION’. What should you do?
- A. Build from it carefully
- B. Do not use it to build or fabricate
- C. Use it if the deadline is urgent
- D. Only use the dimensions
Your Score
| Score | What it suggests |
|---|---|
| Under 50% | You have gaps in the fundamentals. Study the basics and retake the test in a few weeks |
| 50% to 69% | You know the basics but have gaps. Review the explanations for the ones you missed |
| 70% to 84% | Solid working knowledge. You are likely ready for most junior and mid-level tasks |
| 85% and above | Strong command. Prepare for harder practical tasks and interviews |
There are 30 questions, so each is worth a little less than 3.3% of the score.
Answer Key and Explanations
Core Symbols and Conventions (Questions 1 to 10)
1. B. Visible outlines are drawn with the heaviest continuous line. Hidden edges are dashed and centre lines are a long-short-long pattern.
2. B. Centre lines use a chain pattern. Property lines also use a chain pattern but are normally heavier and labelled.
3. B. TYP. means typical: the same dimension applies to similar features not individually dimensioned.
4. B. NTS means not to scale, so do not measure from the drawing.
5. B. Scale is shown in the title block and often beneath each view or detail, because views can have different scales.
6. B. Cutting plane lines with arrows show where the section is taken and from which side it is viewed.
7. B. Revision clouds mark changed areas, usually with a triangle or number that matches the revision table.
8. B. The title block identifies the drawing and its status.
9. B. The Ø symbol means diameter. A radius is shown with R.
10. B. The arc shows the path of the door leaf and which way it opens.
Reading and Checking (Questions 11 to 20)
11. D. A dimension string that does not add up is a drawing error. Ask for clarification rather than guess.
12. D. Written dimensions govern, and prints can be distorted. Drawing notes can state a different rule.
13. D. Detail callouts normally show the detail number above and the sheet number below the line.
14. D. 1:50 is a reduction: 1 mm on the drawing equals 50 mm in reality.
15. D. Level marks give heights relative to a datum, commonly the finished floor level or a geodetic datum, and the drawing should define it.
16. D. Feature control frames state the type of geometric tolerance, its value and any datums.
17. D. Hatching represents cut material, and the legend or the standard identifies the material.
18. D. Symbols vary between standards, so the legend is the first reference.
19. D. Schedules collect item data, which refers back to marks on the plans.
20. D. General notes set shared requirements, so you should read them before reading the details.
Discipline and Practice (Questions 21 to 30)
21. B. Piping drawings often dimension from fitting centre to fitting centre, though conventions vary, so check the project standard.
22. B. The reference line and arrow set the side of the joint to which the weld information applies.
23. B. Panel schedules list circuits and their devices and loads.
24. B. S is used for structural, A for architectural, M for mechanical, E for electrical, P for plumbing and C for civil, although each project can set its own.
25. B. Closely spaced contours indicate a steeper slope.
26. B. A negative grade falls as stationing increases. A positive grade rises.
27. B. Conflicts go to the designer. A written RFI records the question and the answer.
28. B. AFF gives the height of an item above the finished floor level.
29. B. R denotes radius. Revision is usually in a table.
30. B. The status stamp controls the use of the drawing, and only drawings issued for construction should be built from.
What to Do Next
- Test the general knowledge with Free CAD Skills Test (General).
- Test your discipline with Free Drafting Tests by Discipline: Architectural, Structural, MEP, Mechanical and Civil.
- Practise on real sets of drawings. Pick a sheet and write down every symbol you cannot explain.
- Prepare for a hands-on interview with CAD Practical Test Guide: What Employers Test and How to Prepare.
Frequently Asked Questions
Can I take this test without seeing real drawings? Yes, but nothing replaces reading real drawing sets. Use the test to find gaps, then look for those symbols on real sheets.
Are the symbols the same on every project? No. Each office, client and standard can differ. Always check the legend and the general notes.
Why does the test include questions about disagreements between drawings? Because reading a drawing set includes noticing when it contradicts itself.
Is it a certification? No. It is a self-assessment.
Sources
- No external sources. The test reflects the author’s professional experience as a CAD manager and trainer.
Questions and explanations are the author’s own, based on professional experience. Corrections are welcome.
Read before you draw. The best drafters read every sheet.



