Before software, there is drafting. The best CAD people I have worked with could read a drawing, check a dimension in their head and spot a scale error across a room. This test is software-neutral on purpose. It checks the knowledge that stays with you when the software changes: projection, scale, arithmetic, conventions and judgement.
This free test has 30 multiple-choice questions with an answer key that explains every answer.
The Short Answer
- 30 questions: 10 core, 10 practice, 10 judgement.
- No software knowledge needed.
- Includes scale, unit and slope arithmetic.
- It is a self-assessment, not a certification.
- Take it without a calculator first, then check.
How This Test Works
- Take it without help. Use paper and a pencil for the calculations. Do not look up the answers.
- Write your answers down (for example, 1-B, 2-D) before you read the answer key.
- Check yourself against the answer key and read every explanation, including those for questions you got right.
- Score yourself with the bands below.
This is an informal self-assessment, not a certification, and employers’ tests differ. Software questions describe general behaviour. Menus and features vary by version, so check your employer’s version.
The Test (30 Questions)
Core Knowledge (Questions 1 to 10)
Projection, scale, arithmetic and conventions.
1. In North American (third-angle) projection, where is the right-side view placed relative to the front view?
- A. To the left of the front view
- B. To the right of the front view
- C. Below the front view
- D. Above the front view
2. A wall measures 84 mm on a drawing printed at 1:50. What is its real length?
- A. 840 mm
- B. 4,200 mm
- C. 8,400 mm
- D. 420 mm
3. What is 2 inches in millimetres?
- A. 25.4 mm
- B. 50.8 mm
- C. 5.08 mm
- D. 508 mm
4. A room is 6 m by 4.5 m. What is its area?
- A. 10.5 m²
- B. 27 m²
- C. 54 m²
- D. 21 m²
5. A triangle has sides of 3, 4 and 5 units. What do you know about it?
- A. It is an equilateral triangle
- B. It is a right triangle
- C. It has no right angle
- D. It is an isosceles triangle
6. A ramp rises 0.9 m at a slope of 1:12. What run is required?
- A. 1.08 m
- B. 10.8 m
- C. 7.5 m
- D. 12 m
7. What does a dashed (hidden) line normally show?
- A. Centre lines
- B. Edges that are not visible from the current view
- C. Cutting planes only
- D. Dimension limits
8. What does a title block usually contain?
- A. Only the scale
- B. Project name, drawing title, number, date, revision and author or approval information
- C. Only the revision cloud
- D. A list of all layers
9. What is the purpose of section hatching?
- A. To indicate colour
- B. To show cut material in a section view
- C. To show hidden edges
- D. To mark dimensions
10. Which file format is most appropriate for sending a drawing that must not be edited?
- A. DWG
- B. PDF
- C. DXF
- D. RVT
Drafting Practice (Questions 11 to 20)
Tolerances, standards and good habits.
11. What is a tolerance on a dimension?
- A. The scale of the drawing
- B. The colour of the line
- C. A type of arrow
- D. The permitted variation from the stated size
12. A dimension reads 25 ± 0.5 mm. Which measurement is acceptable?
- A. 24.4 mm
- B. 25.6 mm
- C. 26 mm
- D. 24.7 mm
13. Why should dimensions be placed outside the part where possible?
- A. To save ink
- B. To hide errors
- C. To make the file smaller
- D. To keep the view clear and readable
14. What is the purpose of revision control on drawings?
- A. To lock the file forever
- B. To reduce the file size
- C. To change scale
- D. To track what changed, when and why
15. Which drawing needs a licensed professional’s seal in most Canadian jurisdictions?
- A. Any internal sketch
- B. A personal practice drawing
- C. A file rename
- D. One issued for permit or construction where regulations require a professional seal
16. What does a centre line mark?
- A. The edge of a part
- B. A cutting plane
- C. A hidden feature
- D. The centre of circles, symmetrical parts and axes
17. What is a detail view used for?
- A. Showing a project schedule
- B. Replacing the title block
- C. Hiding objects
- D. Showing a small area at a larger scale
18. What should you do before you start work on a drawing someone else prepared?
- A. Delete the layers
- B. Change the units
- C. Purge everything
- D. Check the standards, the xrefs and the revision status
19. Which is the best way to name drawing files?
- A. Use random names
- B. Use the date only
- C. Use your initials only
- D. Follow the project’s agreed convention consistently
20. What is an orthographic drawing?
- A. A 3D rendering
- B. A photo
- C. A topographic map
- D. A 2D representation of an object’s views on perpendicular planes
Professional Judgement (Questions 21 to 30)
Scale, communication and responsibility.
21. A drawing is plotted at 1:20. A 5 m wall appears how long on the sheet?
- A. 25 mm
- B. 250 mm
- C. 100 mm
- D. 2,500 mm
22. What does a leader line connect?
- A. Two layers
- B. A note or label to the feature it describes
- C. Two sheets
- D. Two files
23. What is a good use for layers in an architectural drawing?
- A. Making files larger
- B. Separating walls, doors, dimensions and text so they can be controlled
- C. Hiding the title block
- D. Locking the scale
24. What is the difference between a plan and an elevation?
- A. There is none
- B. A plan is a view from above; an elevation is a side view
- C. A plan is a 3D view
- D. An elevation is a section
25. Which unit system is used for most Canadian construction drawings today?
- A. Imperial only
- B. Metric, with some imperial in certain trades or older projects
- C. Nautical only
- D. Furlongs
26. A scale bar is useful because it
- A. is required by law
- B. stays correct when the drawing is enlarged or reduced
- C. replaces dimensions
- D. changes colour
27. What is an as-built drawing?
- A. A design concept
- B. A drawing that records the actual condition after construction
- C. A permit application
- D. A rendering
28. What should you do if two drawings conflict?
- A. Choose one and say nothing
- B. Raise it with the responsible person and record the resolution
- C. Ignore both
- D. Delete one
29. What is the purpose of a legend or symbol list?
- A. To show the schedule
- B. To explain the symbols and abbreviations used
- C. To list layers
- D. To hide notes
30. Which action best prevents errors when you copy details from an old project?
- A. Paste without review
- B. Check them against the current project’s standards, codes and units
- C. Rename the layers only
- D. Change the colour
Your Score
| Score | What it suggests |
|---|---|
| Under 50% | You have gaps in the fundamentals. Study the basics and retake the test in a few weeks |
| 50% to 69% | You know the basics but have gaps. Review the explanations for the ones you missed |
| 70% to 84% | Solid working knowledge. You are likely ready for most junior and mid-level tasks |
| 85% and above | Strong command. Prepare for harder practical tasks and interviews |
There are 30 questions, so each is worth a little less than 3.3% of the score.
Answer Key and Explanations
Core Knowledge (Questions 1 to 10)
1. B. In third-angle projection, views are placed as if you were looking at the faces of a glass box: the right view sits to the right of the front view and the top view sits above it.
2. B. At 1:50, real length = 84 mm × 50 = 4,200 mm.
3. B. One inch is exactly 25.4 mm, so 2 in = 50.8 mm.
4. B. Area = 6 × 4.5 = 27 m².
5. B. 3² + 4² = 5², so it satisfies the Pythagorean theorem.
6. B. A 1:12 slope means 12 units of run for each unit of rise, so 0.9 × 12 = 10.8 m.
7. B. Hidden lines represent features behind a surface.
8. B. The title block identifies the drawing and its status.
9. B. Hatch patterns identify surfaces cut by the section plane and often indicate material.
10. B. PDF is a fixed document for review and issue. DWG, DXF and RVT can be edited.
Drafting Practice (Questions 11 to 20)
11. D. Tolerances state how much a dimension may vary and still be acceptable.
12. D. The acceptable range is 24.5 mm to 25.5 mm.
13. D. Clear dimension placement reduces confusion and misreading.
14. D. Revision records let everyone know which version is current and what was altered.
15. D. Requirements vary by province and project, and the licensed professional is responsible for sealing the drawings. Always check the local regulator and the project.
16. D. Centre lines identify the axes and centres of features.
17. D. Detail views enlarge areas that need more information.
18. D. Understanding the file setup avoids breaking standards or working on an outdated version.
19. D. A consistent convention makes files searchable and avoids confusion.
20. D. Orthographic projection shows the front, top and side views.
Professional Judgement (Questions 21 to 30)
21. B. 5,000 mm ÷ 20 = 250 mm.
22. B. Leaders attach text to features.
23. B. Layers help control visibility and plotting.
24. B. Plans are horizontal cuts looked at from above; elevations are views of vertical faces.
25. B. Canada uses metric, although imperial can appear in specific trades or older projects. Always confirm the unit convention of the project.
26. B. A ratio such as 1:50 is only valid at the original print size, but a scale bar scales with the drawing.
27. B. As-built drawings show what was actually constructed, including changes.
28. B. Conflicts must be resolved by the designer, and the answer should be documented.
29. B. Legends make a drawing understandable to people unfamiliar with the project.
30. B. Old details may be out of date or not suitable for the current project.
What to Do Next
- Take the software-specific tests: Free AutoCAD Test: Beginner, Intermediate and Advanced and Free Revit and BIM Test.
- Revisit the questions you missed and note the pattern.
- Prepare for a practical test with CAD Practical Test Guide: What Employers Test and How to Prepare.
- Build a portfolio. See CAD Portfolio Guide: Structure, Examples, Template and Checklist.
Frequently Asked Questions
Is this test software-specific? No. It tests general drafting knowledge that applies in any CAD program.
Why is scale arithmetic included? Because scale errors are among the most common drafting mistakes, and employers check them.
Does the seal question mean I need a licence? No. It checks that you know a licensed professional is responsible for sealed drawings.
Is it a certification? No. It is a self-assessment.
Sources
- No external sources. The test reflects the author’s professional experience as a CAD manager and trainer.
Questions and explanations are the author’s own, based on professional experience. Corrections are welcome.
Software changes every few years. Drafting fundamentals do not.



