In-House vs Outsourced vs Offshore Drafting: A Decision Guide

In-House vs Outsourced vs Offshore Drafting: A Decision Guide

Every few years a firm I advise gets an email promising drafting at a fraction of the cost. Sometimes the answer is yes. More often the real cost lands somewhere else: in checking time, rework, confidentiality, time zones and the quiet loss of the people who knew your standards. The right model depends on your work, not on a rate card.

This guide compares three ways to get drafting done, gives you a way to calculate cost per productive hour and lists the risks you must manage.

This guide is general information from a CAD manager’s point of view. It is not legal, HR or immigration advice. Employment, human rights and immigration rules change and differ by province, so check them with your HR adviser, the provincial authority or a lawyer.


The Short Answer

  • In-house gives control, continuity and standards, at the highest fixed cost.
  • Outsourced in Canada (a drafting service, freelancer or staffing agency) gives flexibility and local accountability, at a higher hourly rate and with more briefing time.
  • Offshore can reduce the hourly rate, but adds coordination, review, security and legal considerations. I have not verified offshore rates, so I give none.
  • Decide on the work. Stable, repetitive, standardized work suits outsourcing. Complex, changing, client-facing work with regulatory sealing suits in-house.
  • Calculate cost per productive hour, including review time, rework and management, not only the invoice rate.
  • Many firms use a blend: a core team in-house and a flexible overflow.

The Three Models

In-houseOutsourced in CanadaOffshore
Control over standardsHighMedium, depends on briefingMedium to low, depends on process
Speed to startSlow (hiring, onboarding)FastMedium (setup, briefing)
FlexibilityLowHighHigh
Fixed costHighLowLow
AccountabilityDirectContractual, localContractual, cross-border
Confidentiality controlHighMediumNeeds extra safeguards
Time zone fitSameSimilarOften different
Best forCore, complex, changing workPeaks, specialties, overflowLarge volumes of standardized work with strong review

The table is my professional judgement, not market data.


What Each Option Really Costs

In-house

Use the employee cost: salary plus employer CPP, EI, benefits, workers’ compensation, software, hardware, training and recruiting. For an illustrative $65,000 salary, the annual cost in my hiring kit example is $80,022.55 (1.23 times the salary). See CAD Hiring Kit: Checklist, Scorecard and Evaluation Form.

Now divide by productive hours, not paid hours. If a person is billable 1,400 hours a year (an illustrative figure that depends on your business):

ItemValue
Annual cost (illustrative)$80,022.55
Billable or productive hours (illustrative)1,400
Cost per productive hour$57.16
Compared with the hourly wage equivalent ($65,000 ÷ 2,080 = $31.25)about 1.8 times

The multiple is the point: a person’s hourly pay is not their hourly cost. Do the same with your own figures.

Outsourced in Canada

The invoice rate usually looks high next to a wage. Add the cost of your side: briefing, standards documents, review and corrections, and project management. If review takes 20% of the provider’s hours, you pay for 1.2 hours of someone’s time to get 1 hour of accepted work. Compare that with $57.16 for in-house, or use your own number.

Freelancer break-even (illustrative): at $57.16 per productive hour, a freelancer whose all-in rate is lower than that is cheaper than the in-house person for hours you can actually fill, and more expensive if you need them year-round. Check how the freelance model works in Freelance vs Contract vs Permanent CAD Jobs: The Complete Comparison, and be careful about employee misclassification: if the person works like an employee, the label may not hold. Ask a lawyer or the Canada Revenue Agency.

Offshore

I have no verified, sourced rate for offshore drafting, and quoted rates vary widely by country, skill and scope. Ask for quotes on a sample project, then add:

  • Briefing and standards documentation time
  • Your review and correction time
  • Time lost to time zones and clarifications
  • Security, legal and insurance work
  • Replacement risk if the provider’s staff change

Compare the total with your in-house cost per productive hour.


Decision Framework

Score each question from 1 to 5 for your work, then see which model fits.

QuestionPoints to in-house if…Points to outsourcing if…
How standardized is the work?Highly variable, changes weeklyRepetitive, with clear standards
How much interaction with engineers and clients?ConstantLow, clear handoff
How steady is the volume?Steady all yearPeaks and valleys
How confidential is the project?Highly sensitiveNot sensitive, or protected by contract
How much review can you afford?LimitedA trained checker is available
Is your standards documentation good?No, it lives in people’s headsYes, clear and current
Do you need local knowledge (codes, sites, authorities)?YesNo
Does the work need a professional’s stamp?Yes, close supervisionThe professional reviews outputs

If most answers sit on the left, keep the work in-house. If most are on the right, test outsourcing on a pilot project.


Professional Practice, Sealing and Responsibility

In engineering, architecture and surveying, a licensed professional is responsible for sealed documents. Delegating the drafting does not delegate the responsibility. Provincial regulators have rules for supervision and responsibility, and these differ. Ask your regulator or association what applies to outsourced or offshore work in your province before you contract. I have not summarized provincial rules, because I have not verified them.


Confidentiality, IP and Data

IssueWhat to settle in the contract
ConfidentialityNon-disclosure terms, who may see client files, return or deletion at the end
Intellectual propertyWho owns drawings, templates and models
Data locationWhere files are stored, and whether your client’s contract allows it
SecurityAccess control, VPN or secure file transfer, no personal email
PrivacyWhether personal information is involved, and what rules apply
Insurance and liabilityWho pays for errors, and what insurance exists
SubcontractingWhether the provider can pass work to others
ExitHow you get your files and standards back

Some clients, especially public ones, restrict where data may be stored or who may work on it. Check your contracts. A lawyer can review the agreement.


How to Pilot an Outsourcing Arrangement

  1. Choose a small, well-defined project with clear standards.
  2. Provide templates, standards and a briefing document.
  3. Agree acceptance criteria (what counts as correct) and the number of revision rounds.
  4. Test with a paid sample before a long commitment.
  5. Record your review hours. They are part of the cost.
  6. Compare the total cost, quality and speed with in-house.
  7. Decide after the pilot, and write down why.

The practical test ideas in How to Test CAD Skills When Hiring: Test Design, Scoring and Examples can double as a provider evaluation.


What Happens to Your People

Outsourcing changes your team. Be honest about the plan with the people you have. Staff who see work leaving without explanation will look for new jobs. If the aim is to handle peaks and free your team for more complex work, say so and prove it. See How to Retain CAD Staff: A Retention Strategy Guide.


Common Mistakes

  • Comparing an hourly rate with a salary.
  • Ignoring your own review time.
  • Outsourcing before standards are documented.
  • Skipping the pilot.
  • Not checking client contract restrictions.
  • No exit plan for files and standards.
  • Assuming professional responsibility moves with the work.
  • Outsourcing the work that makes you distinctive.

Frequently Asked Questions

Is offshore drafting cheaper? Sometimes, per invoiced hour. Compare the total cost, including review and risk. I have not verified rates.

Can I outsource sealed work? The professional remains responsible, and rules vary. Ask your regulator.

What about hiring foreign workers into Canada instead? See Hiring Foreign CAD Workers in Canada: LMIA and Work Permit Guide.

How do I find Canadian outsourced drafting? Referrals, professional associations, freelance platforms and drafting firms. See How to Become a Freelance CAD Drafter in Canada: Clients, Rates, Taxes and Tools.

Should I outsource my BIM work? Modeling to a clear standard can be, but coordination benefits from proximity. See How to Hire a BIM Coordinator in Canada.


Sources

Cost inputs are illustrative. The comparison tables and decision framework are the author’s professional judgement. No offshore rate data was used.

Choose the model for the work, then manage it as carefully as you would a new hire.